Leading 10 typical forklift accidents ， forklift operation need to take note of these issues ！.

Do not undervalue the forklift at work. If the operation is not good, there will certainly be severe crashes in minutes, and there are lots of accidents involving forklifts.

Instance 1: The forklift cargo obstructed the vehicle driver's view, and the person in front might not be located, causing a moving accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty products, the workers utilized their body weight as the weight, which virtually triggered casualties.
Situation 3: The width of the forklift freight exceeds the allowable size of the route and hangs on the roadside rack, which almost creates an accident.
Instance 4: Forklift is speeding and surrender during a turn.
Instance 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift lifts the workers unlawfully, the forklift motorist does not wear the seat belt, the forklift lifter drops and the chauffeur is squashed when the forklift surrender.
Situation 7: The forklift driver did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before beginning, observe the environments, and after validating that there are no barriers that impede the safety of driving, beep the horn first and then begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is steady and reputable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles in the sky. When the lots is traveling, the fork should not be elevated too high, which will impact the security of the forklift. .
3. After unloading, the fork must be decreased to the regular driving placement before driving. .
4. When turning, if there are pedestrians or automobiles nearby, the driving signal must be issued first. High-speed doglegs are restricted. High-speed sharp turns will create the automobile to lose lateral security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to switch off the flame and slide, and it is forbidden to brake suddenly while driving with loads unless there are special conditions.
6. When the forklift is running, it has to obey the traffic rules in the factory and have to keep a specific security range from the automobile ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable setting that does not impede the driving, and the gantry must be appropriately slanted back. The tons shall not be increased except when stacking or loading. .
8. The elevation of the lots have to not obstruct the motorist's view. In special situations, when the item affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for workers to base on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be repaired and reported in a timely fashion, and they will never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the range in between the two forks need to be changed as needed to make the lots of the two forks well balanced and not manipulated, and one side of the item need to be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special conditions, security warning signs need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The rate of the automobile should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure Electric Forklift Truck for Warehouse people. .
5. When making use of a fork to fork the goods, the fork should be as deep as feasible under the lots, and it ought to be kept in mind Electric Forklift Truck for Warehouse that the fork tip must not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be slanted forward somewhat when the lots is lowered to allow for simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at high speed and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to loaf the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is forbidden, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to choose, transform pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the appearance needs to be checked, and gas, lubing oil and air conditioning water need to be included.
2. Check the security performance of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the exterior leak ought to also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of " cost-free turning";.
6. Running up and down the incline needs to be slow and consistent, and no switching on the slope is allowed.
7. Do not drive across the gradient. When the gradient is higher than 10%, the lorry should be driven backwards when going downhill;.
8. When the forklift personnel lug the goods and progress, if they experience huge or heavy products and most likely to the vehicle driver's line of vision, they ought to take the reversing workout
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Solitary fork operation is not enabled.
2. It is not allowed to raise the goods for long distance driving.
3. It is not allowed to pick up the goods by passing on the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other hazardous chemicals with forks.
5. It is not enabled to utilize inertia pressure to grab the goods.
6. It is not permitted to use braking force to expatriation round or easy-to-roll objects.
7. It is not permitted to bring people to work on the pallet or fork, and it is purely prohibited to stand under the fork after the fork is increased.
8. Do not drive laterally on slopes
.
Vehicle parking is not allowed under the list below problems.
1. Contours, slim roads, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an barrier on one side of the road, the opposite side of the section with the very same size as the obstacle must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844